This file of echoed input was generated by FAST (v7.02.00d-bjj, 20-Feb-2013) on 15-Nov-2016 at 09:54:09. Turbine input data from file "NRELOffshrBsline5MW_Monopile_DS.fst": NREL 5.0 MW Baseline Wind Turbine for Use in Offshore Analysis. ---------------------- SIMULATION CONTROL -------------------------------------- T Echo - Echo input to "echo.out" 3 ADAMSPrep - ADAMS preprocessor mode 1 AnalMode - Analysis mode 3 NumBl - Number of blades 6.3000E+02 TMax - Total run time 1.2500E-02 DT - Integration time step ---------------------- TURBINE CONTROL ----------------------------------------- 0 YCMode - Yaw control mode 9.9999E+03 TYCOn - Time to enable yaw control 1 PCMode - Pitch control mode 0.0000E+00 TPCOn - Time to enable pitch control 2 VSContrl - Variable-speed-generator control switch 9.9999E+03 VS_RtGnSp - Rated generator speed for simple variable-speed generator control 9.9999E+03 VS_RtTq - Rated generator torque/constant generator torque in Region 3 for simple variable-speed generator control 9.9999E+03 VS_Rgn2K - Generator torque constant in Region 2 for simple variable-speed generator control 9.9999E+03 VS_SlPc - Rated generator slip percentage in Region 2 1/2 for simple variable-speed generator control 2 GenModel - Generator model T GenTiStr - Start generator based upon T: time or F: generator speed T GenTiStp - Stop generator based upon T: time or F: generator power = 0 9.9999E+03 SpdGenOn - Generator speed to turn on the generator 0.0000E+00 TimGenOn - Time to turn on generator 9.9999E+03 TimGenOf - Time to turn off generator 1 HSSBrMode - HSS brake model 9.9999E+03 THSSBrDp - Time to initiate deployment of the HSS brake 9999.9 TiDynBrk - Time to initiate deployment of the dynamic generator brake [CURRENTLY IGNORED] (s) 9.9999E+03 TTpBrDp(1) - Time to initiate deployment of tip brakes 9.9999E+03 TTpBrDp(2) - Time to initiate deployment of tip brakes 9.9999E+03 TTpBrDp(3) - Time to initiate deployment of tip brakes 9.9999E+03 TBDepISp(1) - Deployment-initiation speed for the tip brakes 9.9999E+03 TBDepISp(2) - Deployment-initiation speed for the tip brakes 9.9999E+03 TBDepISp(3) - Deployment-initiation speed for the tip brakes 9.9999E+03 TYawManS - Time to start yaw maneuver 9.9999E+03 TYawManE - Time to end yaw maneuver 0.0000E+00 NacYawF - Final nacelle-yaw angle for maneuvers 9.9999E+03 TPitManS(1) - Time to start pitch maneuvers 9.9999E+03 TPitManS(2) - Time to start pitch maneuvers 9.9999E+03 TPitManS(3) - Time to start pitch maneuvers 9.9999E+03 TPitManE(1) - Time to end pitch maneuvers 9.9999E+03 TPitManE(2) - Time to end pitch maneuvers 9.9999E+03 TPitManE(3) - Time to end pitch maneuvers 0.0000E+00 BlPitch(1) - Initial pitch angle 0.0000E+00 BlPitch(2) - Initial pitch angle 0.0000E+00 BlPitch(3) - Initial pitch angle 0.0000E+00 BlPitchF(1) - Final pitch angle for maneuvers 0.0000E+00 BlPitchF(2) - Final pitch angle for maneuvers 0.0000E+00 BlPitchF(3) - Final pitch angle for maneuvers ---------------------- ENVIRONMENTAL CONDITIONS -------------------------------- 9.8067E+00 Gravity - Gravitational acceleration ---------------------- FEATURE FLAGS ------------------------------------------- T FlapDOF1 - First flapwise blade mode DOF T FlapDOF2 - Second flapwise blade mode DOF T EdgeDOF - First edgewise blade mode DOF False TeetDOF - Rotor-teeter DOF (flag) [unused for 3 blades] T DrTrDOF - Drivetrain rotational-flexibility DOF T GenDOF - Generator DOF T YawDOF - Yaw DOF T TwFADOF1 - First tower fore-aft bending-mode DOF T TwFADOF2 - Second tower fore-aft bending-mode DOF T TwSSDOF1 - First tower side-to-side bending-mode DOF T TwSSDOF2 - Second tower side-to-side bending-mode DOF T CompAero - Compute aerodynamic forces F CompNoise - Compute aerodynamic noise ---------------------- INITIAL CONDITIONS -------------------------------------- 0.0000E+00 OoPDefl - Initial out-of-plane blade-tip deflection 0.0000E+00 IPDefl - Initial in-plane blade-tip deflection 0.0 TeetDefl - Initial or fixed teeter angle (degrees) [unused for 3 blades] 0.0000E+00 Azimuth - Initial azimuth position for blade 1 1.2100E+01 RotSpeed - Initial or fixed rotor speed 0.0000E+00 NacYaw - Initial or fixed nacelle-yaw angle 0.0000E+00 TTDspFA - Initial fore-aft tower-top displacement 0.0000E+00 TTDspSS - Initial side-to-side tower-top displacement ---------------------- TURBINE CONFIGURATION ----------------------------------- 6.3000E+01 TipRad - Preconed blade-tip radius 1.5000E+00 HubRad - Preconed hub radius 1 PSpnElN - Number of the innermost blade element which is still part of the pitchable portion of the blade for partial-span pitch control [1 to BldNodes] [CURRENTLY IGNORED] (-) 0.0 UndSling - Undersling length [distance from teeter pin to the rotor apex] (meters) [unused for 3 blades] 0.0000E+00 HubCM - Distance from rotor apex to hub mass -5.0191E+00 OverHang - Distance from yaw axis to rotor apex or teeter pin 1.9000E+00 NacCMxn - Downwind distance from tower-top to nacelle CM 0.0000E+00 NacCMyn - Lateral distance from tower-top to nacelle CM 1.7500E+00 NacCMzn - Vertical distance from tower-top to nacelle CM 8.7600E+01 TowerHt - Tower height 1.9626E+00 Twr2Shft - Vertical distance from tower-top to rotor shaft 0.0000E+00 TwrRBHt - Tower rigid base height -5.0000E+00 ShftTilt - Rotor shaft tilt angle 0.0 Delta3 - Delta-3 angle for teetering rotors (degrees) [unused for 3 blades] -2.5000E+00 PreCone(1) - Blade coning angle -2.5000E+00 PreCone(2) - Blade coning angle -2.5000E+00 PreCone(3) - Blade coning angle 0.0000E+00 AzimB1Up - Azimuth value to use for I/O when blade 1 points up ---------------------- MASS AND INERTIA ---------------------------------------- 0.0000E+00 YawBrMass - Yaw bearing mass 2.4000E+05 NacMass - Nacelle mass 5.6780E+04 HubMass - Hub mass 0.0000E+00 TipMass(1) - Tip-brake mass 0.0000E+00 TipMass(2) - Tip-brake mass 0.0000E+00 TipMass(3) - Tip-brake mass 2.6079E+06 NacYIner - Nacelle yaw inertia 5.3412E+02 GenIner - Generator inertia about HSS 1.1593E+05 HubIner - Hub inertia about rotor axis ---------------------- DRIVETRAIN ---------------------------------------------- 1.0000E+02 GBoxEff - Gearbox efficiency 9.4400E+01 GenEff - Generator efficiency 9.7000E+01 GBRatio - Gearbox ratio F GBRevers - Gearbox reversal flag 2.8116E+04 HSSBrTqF - Fully deployed HSS brake torque 6.0000E-01 HSSBrDT - Time for HSS-brake to reach full deployment once initiated "Dummy" DynBrkFi - File containing a mech-gen-torque vs HSS-speed curve for a dynamic brake [CURRENTLY IGNORED] (quoted string) 8.6764E+08 DTTorSpr - Drivetrain torsional spring 6.2150E+06 DTTorDmp - Drivetrain torsional damper ---------------------- SIMPLE INDUCTION GENERATOR ------------------------------ 9.9999E+03 SIG_SlPc - Rated generator slip percentage 9.9999E+03 SIG_SySp - Synchronous (zero-torque) generator speed 9.9999E+03 SIG_RtTq - Rated torque 9.9999E+03 SIG_PORt - Pull-out ratio ---------------------- THEVENIN-EQUIVALENT INDUCTION GENERATOR ----------------- 9.9999E+03 TEC_Freq - Line frequency 9998 TEC_NPol - Number of poles 9.9999E+03 TEC_SRes - Stator resistance 9.9999E+03 TEC_RRes - Rotor resistance 9.9999E+03 TEC_VLL - Line-to-line RMS voltage 9.9999E+03 TEC_SLR - Stator leakage reactance 9.9999E+03 TEC_RLR - Rotor leakage reactance 9.9999E+03 TEC_MR - Magnetizing reactance ---------------------- PLATFORM ------------------------------------------------ 2 PtfmModel - Platform model switch PtfmFile - Name of file containing platform properties "NRELOffshrBsline5MW_Platform_Monopile_DS.dat" ---------------------- TOWER --------------------------------------------------- 99 TwrNodes - Number of tower nodes used for analysis TwrFile - Name of file containing tower properties "NRELOffshrBsline5MW_Tower_Monopile_DS.dat" ---------------------- NACELLE-YAW --------------------------------------------- 9.0283E+09 YawSpr - Nacelle-yaw spring constant 1.9160E+07 YawDamp - Nacelle-yaw damping constant 0.0000E+00 YawNeut - Neutral yaw position ---------------------- FURLING ------------------------------------------------- F Furling - Read in additional model properties for furling turbine FurlFile - Name of file containing furling properties "Dummy" ---------------------- ROTOR-TEETER -------------------------------------------- 0 TeetMod - Rotor-teeter spring/damper model {0: none, 1: standard, 2: user-defined from routine UserTeet} (switch) [unused for 3 blades] 0.0 TeetDmpP - Rotor-teeter damper position (degrees) [used only for 2 blades and when TeetMod=1] 0.0 TeetDmp - Rotor-teeter damping constant (N-m/(rad/s)) [used only for 2 blades and when TeetMod=1] 0.0 TeetCDmp - Rotor-teeter rate-independent Coulomb-damping moment (N-m) [used only for 2 blades and when TeetMod=1] 0.0 TeetSStP - Rotor-teeter soft-stop position (degrees) [used only for 2 blades and when TeetMod=1] 0.0 TeetHStP - Rotor-teeter hard-stop position (degrees) [used only for 2 blades and when TeetMod=1] 0.0 TeetSSSp - Rotor-teeter soft-stop linear-spring constant (N-m/rad) [used only for 2 blades and when TeetMod=1] 0.0 TeetHSSp - Rotor-teeter hard-stop linear-spring constant (N-m/rad) [used only for 2 blades and when TeetMod=1] ---------------------- TIP-BRAKE ----------------------------------------------- 0.0000E+00 TBDrConN - Tip-brake drag constant during normal operation 0.0000E+00 TBDrConD - Tip-brake drag constant during fully-deployed operation 0.0000E+00 TpBrDT - Time for tip-brake to reach full deployment once released ---------------------- BLADE --------------------------------------------------- BldFile(1) - Names of files containing blade properties NRELOffshrBsline5MW_Blade.dat BldFile(2) - Names of files containing blade properties NRELOffshrBsline5MW_Blade.dat BldFile(3) - Names of files containing blade properties NRELOffshrBsline5MW_Blade.dat ---------------------- AERODYN ------------------------------------------------- ADFile - Name of file containing AeroDyn parameters "NRELOffshrBsline5MW_AeroDyn.ipt" ---------------------- NOISE --------------------------------------------------- NoiseFile - Name of file containing aerodynamic noise parameters "Dummy" ---------------------- ADAMS --------------------------------------------------- ADAMSFile - Name of file containing ADAMS-specific properties "NRELOffshrBsline5MW_ADAMSSpecific.dat" ---------------------- LINEARIZATION CONTROL ----------------------------------- LinFile - Name of file containing FAST linearization parameters "NRELOffshrBsline5MW_Linear.dat" ---------------------- OUTPUT -------------------------------------------------- T SumPrint - Print summary data to "*.fsm" 1 OutFileFmt - Format for output file(s) T TabDelim - Use tab delimiters in text output file OutFmt - Output format for text tabular data "ES10.3E2" 3.0000E+01 TStart - Time to begin tabular output 1 DecFact - Decimation factor for tabular output 1.0000E+00 SttsTime - Amount of time between screen status messages -3.0953E+00 NcIMUxn - Downwind distance from the tower-top to the nacelle IMU 0.0000E+00 NcIMUyn - Lateral distance from the tower-top to the nacelle IMU 2.2334E+00 NcIMUzn - Vertical distance from the tower-top to the nacelle IMU 1.9120E+00 ShftGagL - Distance from hub or teeter pin to shaft strain gages 3 NTwGages - Number of tower "strain-gage" output stations TwrGagNd - List of tower nodes that have strain gages 10 19 28 3 NBlGages - Number of blade "strain-gage" output stations BldGagNd - List of blade nodes that have strain gages 5 9 13 OutList - The next line(s) contains a list of output parameters. See OutList.txt for a listing of available output channels, (-) OutList - Output list "WindVxi , WindVyi , WindVzi" OutList - Output list "WaveElev" OutList - Output list "GenPwr , GenTq" OutList - Output list "OoPDefl1 , IPDefl1 , TwstDefl1" OutList - Output list "BldPitch1" OutList - Output list "Azimuth" OutList - Output list "RotSpeed , GenSpeed" OutList - Output list "TTDspFA , TTDspSS , TTDspTwst" OutList - Output list "TeetDefl , TeetDefl" OutList - Output list "PtfmTDxi , PtfmTDyi , PtfmRDxi , PtfmRDyi" OutList - Output list "TeetDefl , TeetDefl" OutList - Output list "Spn2MLxb1, Spn2MLyb1" OutList - Output list "RootFxc1 , RootFyc1 , RootFzc1" OutList - Output list "RootMxc1 , RootMyc1 , RootMzc1" OutList - Output list "RotTorq , LSSGagMya, LSSGagMza" OutList - Output list "YawBrFxp , YawBrFyp , YawBrFzp" OutList - Output list "YawBrMxp , YawBrMyp , YawBrMzp" OutList - Output list "TwHt3MLxt, TwHt3MLyt" OutList - Output list "TwHt2MLxt, TwHt2MLyt" OutList - Output list "TwHt1MLxt, TwHt1MLyt" OutList - Output list "TwrBsFxt , TwrBsFyt , TwrBsFzt" OutList - Output list "TwrBsMxt , TwrBsMyt , TwrBsMzt" OutList - Output list "TeetDefl , TeetDefl , TeetDefl , TeetDefl" OutList - Output list "PtfmSurge, PtfmSway , PtfmRoll , PtfmPitch" OutList - Output list "END" Platform input data from file ".\NRELOffshrBsline5MW_Platform_Monopile_DS.dat": ---------------------- FEATURE FLAGS (CONT) ------------------------------------ T PtfmSgDOF - Platform surge DOF T PtfmSwDOF - Platform sway DOF F PtfmHvDOF - Platform heave DOF T PtfmRDOF - Platform roll DOF T PtfmPDOF - Platform pitch DOF F PtfmYDOF - Platform yaw DOF ---------------------- INITIAL CONDITIONS (CONT) ------------------------------- 0.0000E+00 PtfmSurge - Initial or fixed platform surge 0.0000E+00 PtfmSway - Initial or fixed platform sway 0.0000E+00 PtfmHeave - Initial or fixed platform heave 0.0000E+00 PtfmRoll - Initial or fixed platform roll 0.0000E+00 PtfmPitch - Initial or fixed platform pitch 0.0000E+00 PtfmYaw - Initial or fixed platform yaw ---------------------- TURBINE CONFIGURATION (CONT) ---------------------------- 5.6000E+01 TwrDraft - Downward distance from ground [onshore] or MSL [offshore] to tower base platform connection 5.6000E+01 PtfmCM - Downward distance from ground [onshore] or MSL [offshore] to platform CM 5.6000E+01 PtfmRef - Downward distance from ground [onshore] or MSL [offshore] to platform reference point ---------------------- MASS AND INERTIA (CONT) --------------------------------- 0.0000E+00 PtfmMass - Platform mass 0.0000E+00 PtfmRIner - Platform inertia for roll tilt rotation about the platform CM 0.0000E+00 PtfmPIner - Platform inertia for pitch tilt rotation about the platform CM 0.0000E+00 PtfmYIner - Platform inertia for yaw rotation about the platform CM ---------------------- PLATFORM (CONT) ----------------------------------------- 0 PtfmLdMod - Platform loading model switch ---------------------- TOWER (CONT) -------------------------------------------- 2 TwrLdMod - Tower loading model switch 0.0 TwrDiam - Tower diameter in Morison's equation (meters) [used only when TwrLdMod=1] 0.0 TwrCA - Normalized hydrodynamic added mass coefficient in Morison's equation (-) [used only when TwrLdMod=1] [determines TwrCM=1+TwrCA] 0.0 TwrCD - Normalized hydrodynamic viscous drag coefficient in Morison's equation (-) [used only when TwrLdMod=1] ---------------------- WAVES --------------------------------------------------- 1.0270E+03 WtrDens - Water density 2.0000E+01 WtrDpth - Water depth 2 WaveMod - Wave kinematics model switch 3 WaveStMod - Model switch for stretching incident wave kinematics to instantaneous free surface 3.6300E+03 WaveTMax - Analysis time for incident wave calculations 2.5000E-01 WaveDT - Time step for incident wave calculations 5.0000E+00 WaveHs - Significant wave height 1.2400E+01 WaveTp - Peak spectral period WavePkShp - Peak shape parameter "DEFAULT" 0.0000E+00 WaveDir - Wave heading direction 123456789 WaveSeed(1) - First random seed 1011121314 WaveSeed(2) - Second random seed True WaveNDAmp - Normally-distributed amplitudes in incident waves spectrum (flag) [used only when WaveMod=2 or 3] "Dummy" GHWvFile - Root name of GH Bladed files containing wave data (quoted string) [used only when WaveMod=4]